Finngard Silikonihartsimaali

Water-borne, silicone resin paint.

M1 Avainlippu_NEW

Finngard Silikonihartsimaali

Water-borne, silicone resin paint.

  • 805
  • 4 m²/l
  • 6 m²/l
  • 12 h

Finish

  • Full matt

Description

Water-borne, silicone resin paint.


Product Features

For painting exterior concrete surfaces and solid plaster surfaces.


Recommended Uses

Residential, commercial, industrial and storage buildings and others.


Coverage

4-6 m²/l one coat. Coverage is affected by the roughness and porosity of the surface as well as the application method and conditions.


Application Method

brush, roller, spraying


Application Conditions

The surface to be painted must be dry, the temperature at least +5°C and the relative humidity of the air below 80%. Do not apply in strong sunlight.


Surface preparation

Unpainted surfaces: New concrete and plaster surfaces must be sufficiently dried and hardened before the surface treatment. Among other things, the trying and hardening times depend on the composition of the rendering surface (e.g. lime-concrete ratio), on environmental conditions and on the thickness of the layer. Clean the unpainted surfaces of any dirt, dust and salt. Surfaces with mold, moss etc. are cleaned with Tikkurila Homeenpoisto in accordance with the instructions. Smooth, glassy concrete surfaces must always be treated mechanically to create an appropriate surface profile and remove any laitance. Concrete surfaces with a lot of pores are recommended to be leveled with Finnseco Polytop mortar or Finnseco Leveling Render. Previously painted surface: Surfaces are cleaned by removing any dirt, dust or salt. Surfaces with mold, moss etc. are cleaned with Tikkurila Homeenpoisto in accordance with the instructions. Remove any flaking, chalky and poorly adhering paint coats. Choose the removal method according to the strength of the substrate and type of paint to be removed (e.g. wire brush, pressure washing with hot water or wet sand-blasting). Perform the required repairs, patching and leveling with Finnseco products according to their instructions. Make necessary plastering repairs with suitable plasters to the level and structure of the surrounding surface.


Painting

First coat:

a) Priming and painting The surface to be treated is primed with Tikkurila Silicone Primer; see Priming. Apply two coats of Finngard Silicone Resin Paint. The drying time between the two coats of paint should be at least 12 hours. Finngard Silicone Resin Paint can be thinned with water max. 5-10% for the first coat. b) Priming and painting The surfaces are primed with a mixture of Tikkurila Primer Gel and Finngard Silicone Resin Paint. The mixing ratio is two 1-liter cans of Primer Gel into one 20-liter can of Finngard Silicone Resin Paint. Stir the mixture of Primer Gel and Finngard Silicone Resin Paint thoroughly before use (approx. 5 minutes mechanically). If necessary, thin the mixture with water max. 5% (rinse the Primer Gel container with the water used for thinning). Use the mixture within 24 hours of mixing. The finishing painting is done once, no earlier than 12 hours after the priming, using unthinned Finngard Silicone Resin Paint. c) Painting The painting is done twice using Finngard Silicone Resin Paint. The drying time between the two coats of paint should be at least 12 hours. If required, Finngard Silicone Resin Paint can be thinned with water (max. 5-10%) for the first coat. NOTE Finngard Silicone Resin Paint is stirred comprehensively before use. Reserve enough paint from the same production batch for uniform color surface. Should you need to use different production batches, paint the area between the old and new batch with a 1:1 mix of the old and new paint. Arrange the work so that the transition between the paint batches is as inconspicuous as possible. When treating a substrate containing asbestos, follow the Government Decision on Asbestos Work (1380/1994) and the related Decrees 318/2006 and 863/2010. Surfaces intended to be left unpainted must be protected for the duration of the work. Mechanical stresses can cause lighter marks, in particular with dark painted surfaces. This is a typical product feature for all matte façade paints, which however has no influence on the product’s technical functionality.


Maintenance Painting:

Finngard Silicone Resin Paint or Kivisil Façade Paint are suitable for maintenance treatment of surfaces painted with Finngard Silicone Resin Paint.


Maintenance Instructions

Dirty surfaces can be carefully washed with a pressure washer without any detergent no earlier than one month after painting. The washing may leave permanent marks on the surface, so the area to be washed should be designed inconspicuously following the lines of the structure. It is recommended to remove any loose dirt dry with a soft brush, avoiding abrasion. For removing algae and mold, use Tikkurila Homeenpoisto and rinse thoroughly according to instructions. NB. Surfaces must always be retreated after mold removal.


VOC

(cat A/c) 40g/l (2010) Finngard Silicone Resin Coating contains VOC max. 40g/l.


Excellent water repellency, good water vapor permeability

The excellent water repellency and good water vapor permeability of Finngard Silicone Resin Paint ensure that structures remain dry.

Product usp1prof_img
Excellent water repellency, good water vapor permeability

Long maintenance treatment interval

Finngard Silicone Resin Paint is a durable facade paint that lengthens the maintenance painting interval.

Product usp2prof_img
Long maintenance treatment interval

M1-approved facade paint

Finngard Silicone Resin Paint has received an M1 category for its low emissions.

Product usp3prof_img
Rooftops over Helsinki
English
has been added to saved.
has been removed from saved.
en