Biorid Spray

BioRid Spray is a water-borne functional coating containing micropores, which eliminate moisture and keep the surface dry. BioRid Spray is especially suitable for new and previously painted surfaces in conditions where protection of the paint film from mold contamination is required.

  • Wide range of use
  • Sprayable coating
  • Forms a flexible and porous coating layer
  • 805
  • 1 m²/l
  • 1.6 m²/l
  • 12 h
  • 8 h

Finish

  • Matt

Description

BioRid Spray is a water-borne functional coating containing micropores, which eliminate moisture and keep the surface dry. BioRid Spray is especially suitable for new and previously painted surfaces in conditions where protection of the paint film from mold contamination is required.


Product Features

BioRid Spray is suitable for interior coating of such facilities as cellars, parking garages, food industries (especially breweries), warehouses and animal husbandry operations. BioRid Spray is not suitable for unpainted wooden surfaces. Read the application instructions carefully before starting the painting work. The problems caused by insufficient ventilation or structural problems cannot be repaired with BioRid products.


Recommended Uses

BioRid Spray is suitable for the first time and maintenance painting of interior walls and ceilings. For concrete, plane, gypsum board, brick and metal surfaces according to instructions. Application on steel surfaces requires an anti-corrosion primer.


Coverage

Depending on the surfaces. For effective protection the coverage should be about 1.0-1.6 m²/l (or spreading quantity 750-1200g/ m²).


Thinner

Waterborne


Application Method

spraying, brush, roller


Storage

Protect from frost and direct sunlight. In dry and cool place. Close can carefully for next use. Badly closed or short cans endure badly long-time storage.


Application Conditions

The surface to be painted must be dry, the temperature at least +5°C and the relative humidity of the air below 80%.


Surface preparation

Unpainted surfaces: Remove dirt and dust from the unpainted surfaces. Fill the surfaces with suitable Presto or Prestonit filler, if needed. Prime porous and absorbing surfaces with ProSeal primer. Unpainted molded surfaces: Apply BioWash according to the instructions. Allow the surface to dry. For finishing the cleansing, spread the BioWash, diluted with water 1:50, to the whole surface. Let the surface dry. Fill cracks and holes with a suitable Presto or Prestonit filler. Prime porous and absorbing surfaces with ProSeal primer. Use BioRid for the surface treatment within 24 hours. Previously painted molded surfaces: Apply BioWash according to the instructions. Allow the surface to dry. For finishing the cleansing, spread the BioWash, diluted with water 1:50, to the whole surface. Let the surface dry. Remove old, flaky paint and sand the hard and shiny surfaces matt. Fill the cracks and holes with a suitable Tikkurila Presto or Prestonit filler.


Painting

First coat:

Stir BioRid Spray well before use and thin with water, if necessary. Apply 1-2 times. Edges can be coated by brush. NOTE! Surfaces treated with BioRid must be maintenance-treated with the same product so that they maintain their properties. Surfaces coated with BioRid Spray should not be recoated with other paints or coatings, because that would result in the loss of the desired properties.


Maintenance Painting:

Surfaces coated with BioRid Spray should be recoated with the same product if needed, to retain its properties.


Cleaning of tools

Remove excess paint from tools and clean with water. Tikkurila Pensselipesu Tool Cleaner is recommended to remove slightly hardened paint.


Maintenance Instructions

Avoid high-pressure cleaning.


VOC

(cat A/a) 30g/l (2010) BioRid Spray contains VOC max. 30g/l.


Wide range of use

BioRid Spray is especially suitable for new and previously painted surfaces in conditions where protection of the paint film from mold contamination is required, such as living facilities, bathrooms, cellars, parking garages, food industry premises, warehouses and animal husbandry operations.

Product usp1prof_img
Wide range of use

Sprayable coating

The product is suitable for spray application.

Product usp2prof_img
Sprayable coating

Forms a flexible and porous coating layer

The coating temporarily collects condensed water, and when the surface temperature is above the dew point, the moisture evaporates into the air. Due to the micro-pore technology, evaporation is very fast.

English
Hello!

You’re visiting Tikkurila website from United Kingdom. Would you like to visit the local UK site?

has been added to saved.
has been removed from saved.
en